|
A - KLEEN GROUND (Decarb-free)
|
|
|
Surface
ground/fine-milled flats and squares
|
|
|
|
Thickness
|
+0.015"/+0.030
|
|
|
Width
|
+0.015"/+0.025"
|
|
|
|
B - KLEEN MACHINED (Decarb-free) Flats
and Squares
|
|
|
Surface
milled < 20" thick
|
+0.100"/+0.180"
|
|
|
Surface
milled 20" thick and over
|
+0.125"/+0.3125"
|
|
|
|
C - KLEEN PEELED (Decarb-free) Rounds
|
|
|
Peeled
Rounds, 1/2" - 1 7/8" diameter
|
+0.015"/+0.030"
|
|
|
|
D - KLEEN TURNED (Decarb-free) Rounds
|
|
|
Turned
Rounds 2" diameter and over
|
|
|
|
2"
- 3"
|
+0.035"/+0.045"
|
|
|
3
1/4" - 4 1/2"
|
+0.045"/+0.065"
|
|
|
4
3/4" - 7"
|
+0.080"/+0.120"
|
|
|
7
1/2" - 9 1/2"
|
+0.080"/+0.155"
|
|
|
10"
and up
|
+0.080"/+0.195"
|
|
|
|
E - HOT-ROLLED (Unmachined) Flats and
Squares
|
|
|
Flats
and Squares (Rolled Bar)
|
Thickness
0/+0.020" to 0/+0.060"
|
|
|
|
Width
0/+0.040" to 0/+0.100"
|
|
|
|
(Depending
on Section)
|
|
|
Flats
(Rolled Plate)
|
|
|
|
<
1 7/8" Thick
|
+0.125"/+0.185"
|
|
|
2 - 2
7/8" Thick
|
+0.188"/+0.288"
|
|
|
>
2 7/8" Thick
|
+0.188"/+0.338"
|
|
|
|
F - FINE MACHINED T&B PLATE
|
|
|
Thickness
|
+0.015"/+0.030"
|
|
|
Width
|
+0.100"/+0.180"
|
|
|
|
|
|
G - SAW CUT TOLERANCE - ROUNDS
|
|
|
1/2" – 15"
diameter
|
|
|
|
Cut to Finish – plus
1/4"
oversize
|
|
|
|
Cut to Size – plus 1/8"
oversize
|
|
|
|
|
|
>
15" – 20" diameter
|
|
|
|
Cut to Finish – plus
3/8"
oversize
|
|
|
|
Cut to Size – plus 1/8"
oversize
|
|
|
|
|
|
>
20" – 26" diameter
|
|
|
|
Cut to Finish – >
3/8"
oversize
|
|
|
|
Cut to Size – > 1/8"
oversize
|
|
|
|
|
H - SAW CUT TOLERANCE - FLATS
|
|
|
>
1" – 4" thick; up to 36" wide
|
|
|
|
Cut to Finish – >
1/2" oversize
|
|
|
|
Cut to Size – > 1/8"
oversize
|
|
|
|
|
|
>
4" thick and widths 36" and wider
|
|
|
|
Cut to Finish – >
3/8"
oversize
|
|
|
|
Cut to Size – > 1/8"
oversize
|
|
|
|
|
Bohler-Uddeholm Limited
|
|
“Known for Quality, Remembered
for Service”
|
|
1-800-665-8335
| www.bucanada.ca
|
|
|
|
This
document is intended to provide a general guideline on standard finishes
and tolerances. It should not
therefore be construed as a warranty of a specific size tolerance. Tolerance may vary on size. Please refer to our website
www.bucanada.ca for the latest information. This document is uncontrolled when
printed. Rev. February 8, 2011.
|